2610ROMMON下灌IOS

　　rommon 60 > set IP_ADDRESS 10.16.131.115 　　usage: set 　　rommon 61 > "IP_ADDRESS=10.16.1.2" 　　rommon 62 > "IP_SUBNET_MASK=255.255.255.0" 　　rommon 63 > "DEFAULT_GATEWAY=10.16.1.1" 　　rommon 64 > "TFTP_SERVER=10.16.1.4" 　　rommon 65 > "TFTP_FILE=c2600-i-mz.121-5.T8" 　　rommon 66 > tftpdnld 　　　　 IP_ADDRESS: 10.16.1.2 　　 IP_SUBNET_MASK: 255.255.255.0 　　 DEFAULT_GATEWAY: 10.16.1.1 　　 TFTP_SERVER: 10.16.1.4 　　 TFTP_FILE: c2600-i-mz.121-5.T8 　　　　Invoke this command for disaster recovery only. 　　WARNING: all existing data in all partitions on flash will be lost! 　　Do you wish to continue? y/n: [n]: y 　　　　Receiving c2600-i-mz.121-5.T8 from 10.16.1.4 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 　　!!!!!!! 　　File reception completed. 　　Copying file c2600-i-mz.121-5.T8 to flash. 　　Erasing flash at 0x607c0000 　　program flash location 0x604e0000 　　rommon 67 > 　　rommon 67 > 　　rommon 67 > 　　rommon 67 > boot 　　program load complete, entry point: 0x80008000, size: 0x4e02f0 　　Self decompressing the image : ################################################# 　　################################################################################ 　　################################################################################ 　　################################################################################ 　　################################################################################ 　　################################################################################ 　　################################################################################ 　　################################################################################ 　　### [OK] 　　　　Smart Init is enabled 　　smart init is sizing iomem 　　ID MEMORY_REQ TYPE 　　000091 0X00092280 C2600 single Ethernet 　　 0X000F34A8 public buffer pools 　　 0X00211000 public particle pools 　　TOTAL: 0X00396728 　　　　If any of the above Memory Requirements are 　　"UNKNOWN", you may be using an unsupported 　　configuration or there is a software problem and 　　system operation may be compromised. 　　Rounded IOMEM up to: 4Mb. 　　Using 12 percent iomem. [4Mb/32Mb] 　　　　 Restricted Rights Legend 　　　　Use, duplication, or disclosure by the Government is 　　subject to restrictions as set forth in subparagraph 　　(c) of the Commercial Computer Software - Restricted 　　Rights clause at FAR sec. 52.227-19 and subparagraph 　　(c) (1) (ii) of the Rights in Technical Data and Computer 　　Software clause at DFARS sec. 252.227-7013. 　　　　 cisco Systems, Inc. 　　 170 West Tasman Drive 　　 San Jose, California 95134-1706 　　　　　　　　Cisco Internetwork Operating System Software 　　IOS (tm) C2600 Software (C2600-I-M), Version 12.1(5)T8, RELEASE SOFTWARE (fc1) 　　TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support 　　Copyright (c) 1986-2001 by cisco Systems, Inc. 　　Compiled Mon 07-May-01 17:57 by ccai 　　Image text-base: 0x80008088, data-base: 0x80972320 　　　　cisco 2610 (MPC860) processor (revision 0x203) with 28672K/4096K bytes of memory 　　. 　　Processor board ID JAD05090M7A (447016375) 　　M860 processor: part number 0, mask 49 　　Bridging software. 　　X.25 software, Version 3.0.0. 　　1 Ethernet/IEEE 802.3 interface(s) 　　2 Serial network interface(s) 　　32K bytes of non-volatile configuration memory. 　　8192K bytes of processor board System flash (Read/Write) 　　　　　　　　Press RETURN to get started! 　　　　　　00:00:12: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up 　　00:00:12: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up 　　00:00:12: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down 　　00:00:13: %SYS-5-CONFIG_I: Configured from memory by console 　　00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed s 　　tate to up 　　00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed sta 　　te to down 　　00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed sta 　　te to down 　　00:00:14: %LINK-5-CHANGED: Interface Serial0/1, changed state to administrativel 　　y down 　　00:00:15: %SYS-5-RESTART: System restarted -- 　　Cisco Internetwork Operating System Software 　　IOS (tm) C2600 Software (C2600-I-M), Version 12.1(5)T8, RELEASE SOFTWARE (fc1) 　　TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support 　　Copyright (c) 1986-2001 by cisco Systems, Inc. 　　Compiled Mon 07-May-01 17:57 by ccai 　　Cisco2610-003> 　　　　Cisco2610-003>en