升级线路卡固件在Cisco12000系列互联网路由器
日期：2007-09-16 荐：
前言 本文在Cisco 12000系列互联网路由器线路卡描述如 何在Cisco IOS软件升级以后升级® 微码。 升级线路卡固件取消 警告：老... 消息从 show version命令输出在路由 器。 逐步程序
直到线路卡在允许状态，请勿使用 upgrade 命令在本文。您能验证线路卡的状态用 show gsr命令。关于运 行Cisco IOS软件版本11.2(15)gs2以上的路由器，参见 此信息。 注意： 如果 升级ROM监控器，您 必须 重新载入线路卡。 一旦Cisco IOS软 件被升级了并且路由器被重新载入了，这不 意味着线路卡被升级了到最新的固件。 确定如 果有老版本问题，使用 show version命令，如下所示。 注意 警告消息在下面的show version命令输出的 底部。这些警告消息指 示什么需要被升级。 mfr-2# show version Cisco Internetwork Operating System Software IOS (tm) GS Software (GSR-P-M), Version 11.2(15)GS1a, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Copyright (c) 1986-1998 by cisco Systems, Inc. Compiled Mon 28-Dec-98 14:39 by tamb Image text-base: 0x60010900, data-base: 0x606C4000 ROM: System Bootstrap, Version 11.2(9)GS5, [tamb 176] EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) mfr_2 uptime is 4 minutes System returned to ROM by reload System image file is "slot0:gsr-p-mz.112-15.GS1a", booted via slot0: cisco 12008/GRP (R5000) processor (revision 0x01) with 262144K bytes of memory. R5000 processor, Implementation 35, Revision 2.1 (512KB Level 2 Cache) Last reset from power-on 1 Clock Scheduler Card(s) 1 Quad-port OC3c ATM controller (4 ATM). 1 Single-port OC12c ATM controller (1 ATM). 1 four-port OC3 POS controller (4 POS). 1 Ethernet/IEEE 802.3 interface(s) 5 ATM network interface(s) 4 Packet over SONET network interface(s) 507K bytes of non-volatile configuration memory. 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x102 WARNING: Old Rom Monitor in slot 0 Use "upgrade rom-monitor" command to update the image WARNING: Old Fabric Downloader in slot 0 Use "upgrade fabric-downloader" command to update the image WARNING: Old Rom Monitor in slot 1 Use "upgrade rom-monitor" command to update the image WARNING: Old Fabric Downloader in slot 1 Use "upgrade fabric-downloader" command to update the image WARNING: Old Rom Monitor in slot 2 Use "upgrade rom-monitor" command to update the image WARNING: Old Fabric Downloader in slot 2 Use "upgrade fabric-downloader" command to update the image 从以上警告消息 ，我们能发现我们需要升级ROM监控器和矩阵下载程序。 使用 show diag 命令确定什么线路卡您升级和其当前状态。 注意线路卡在一 个允许状态(IOS RUN)，如显示在下面的 show diag命令输出。当 线路卡在一个允许状态时，您能升级固件。 mfr_2#show diag 0 SLOT 0 (RP/LC 0 ): 4 Port Packet Over SONET OC-3c/STM-1 Multi Mode MAIN: type 33, 800-2396-02 rev A0 dev 16777215 HW config: 0x01 SW key: FF-FF-FF PCA: 73-2147-05 rev A0 ver 4 HW version 1.1 S/N CAB02040049 MBUS: MBUS Agent (1) 73-2146-06 rev A0 dev 0 HW version 1.1 S/N CAB014600ME Test hist: 0xFF RMA#: FF-FF-FF RMA hist: 0xFF DIAG: Test count: 0xFFFFFFFF Test results: 0xFFFFFFFF MBUS Agent Software version 01.35 (RAM) (ROM version is 01.33) Using CAN Bus A ROM Monitor version 0E.00 Fabric Downloader version used 00.13 (ROM version is 11.03) Board is analyzed Board State is Line Card Enabled (IOS RUN ) Insertion time: 00:00:11 (00:04:16 ago) DRAM size: 268435456 bytes FrFab SDRAM size: 67108864 bytes ToFab SDRAM size: 67108864 bytes 下一个步骤将升级线路卡。执行此，使用 upgrade命令。 下面是 upgrade命令选项 列表。 mfr_2#upgrade ? all all GSR rom images fabric-downloader fabric downloader mbus-agent-rom mbus agent rom post Power On Self Test rom-monitor rom monitor 由于有一个ROM监控器警告在 show version命令输出，您 在卡需要升级ROM监控器。upgrade命令在句法示例显示如下 ： mfr_2#upgrade rom-monitor ? all all slots slot slot number <cr> mfr_2#upgrade rom-monitor slot ? <0-7> slot number mfr_2#upgrade rom-monitor slot 0 ========= Line Card (Slot 0) ======= EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv
mfr_2# SLOT 0:Upgraded linecard ROM monitor successfully 其次，升级矩阵下载程序。 upgrade 命令在句法示例显示如下： mfr_2#upgrade fabric-downloader slot 0 ========= Line Card (Slot 0) ======= EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv mfr_2# SLOT 0:Upgraded linecard fabric loader successfully 因为有卡在插槽1和插槽2，您能升级那些。 upgrade命令在句法示例显示如下： mfr_2#upgrade all ? all all slots slot slot number <cr> mfr_2#upgrade all all This will take around 7-10 minutes for a full chassis Ensure that GSR is not power cycled during the upgrade Premature termination of this command may render the GSR inoperable Please consult the documentation for more information Continue ? [no]: yes Starting upgrade, please wait Upgrading line card rom ========= Line Card (Slot 0) ======= EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv ========= Line Card (Slot 1) ======= SLOT 0:Upgraded linecard ROM monitor successfully EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv ========= Line Card (Slot 2) ======= SLOT 1:Upgraded linecard ROM monitor successfully EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv Upgrading line card floader ========= Line Card (Slot 0) ======= SLOT 2:Upgraded linecard ROM monitor successfully EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv ========= Line Card (Slot 1) ======= SLOT 0:Upgraded linecard fabric loader successfully EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv ========= Line Card (Slot 2) ======= SLOT 1:Upgraded linecard fabric loader successfully EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv SLOT 2:Upgraded linecard fabric loader successfully Upgrading the MBUS agent rom on slot 0 rom programmed successfully with 255 retries Upgrading the MBUS agent rom on slot 1 rom programmed successfully with 255 retries Upgrading the MBUS agent rom on slot 2 rom programmed successfully with 255 retries Upgrading the MBUS agent rom on slot 17 rom programmed successfully with 255 retries Upgrading the MBUS agent rom on slot 24 rom programmed successfully with 255 retries Upgrading the MBUS agent rom on slot 7 rom programmed successfully with 255 retries Upgrading grp rom in slot 7 The current revision of GRP ROM is: 175 The new revision of GRP ROM will be: 175 NOTE: 1) GRP ROM upgrade typically takes 30 to 240 seconds. 2) After GRP ROM upgrade the GRP will be reset. Continue GRP ROM upgrade? [yes/no]: n 注意： 在本例中，因为 GRP ROM当前修正与新修
标签：