6509配置双引擎冗余
日期：2007-05-11 荐：
#version 6.3(1) ! set password $2$hodC$6G9acb2epHleGd7Hy6qA8. set enablepass $2$.dxG$ujEuGXH9VoewvKJeTqN.D. 给交换机设置使能口令 ! #system set system name switch 设置交换机名字
set system highavailability enable 实现高性能热备 ! #! #vtp set vtp domain net 设置VTP 域名 set vlan 1 name default type ethernet mtu 1500 said 100001 state active set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state active stp ibm set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active stp ibm set vlan 10,20,30,40-41,50,60,70,80 set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state active mode srb aremaxhop 7 stemaxhop 7 backupcrf off ! #ip set interface sc0 20 10.35.50.253/255.255.255.0 10.35.50.255 设置交换机ip地址 需要根据交换机ip地址属于那个vlan来确定ip地址的vlan号 set ip route 0.0.0.0/0.0.0.0 10.35.50.254 设置交换机静态路由 set ip alias default 0.0.0.0 set ip alias apple 10.35.50.251 设置地址映射 举例：原来telnet 10.35.50.251 .现在可以直接telnet apple 。作用一样。 set ip alias apple2 10.35.50.250 ! #set boot command set boot config-register 0x2 set boot system flash bootflash:cat6000-sup2.6-3-1.bin 设置启动交换机时加载系统操作系统。 ! #port channel #module 1 : 2-port 1000BaseX Supervisor ! #module 2 : 2-port 1000BaseX Supervisor ! #module 3 : 8-port 1000BaseX Ethernet set vlan 20 3/1-6 把端口划分进具体vlan里面，根据网络设计方案具体确定端口用户属于那个vlan set vlan 60 3/7-8 set port name 3/1 ibmweb link 给端口命名，方便管理 ! #module 4 : 48-port 10/100BaseTX Ethernet set vlan 20 4/5-48 set vlan 70 4/1-4 set trunk 4/5 on dot1q 1-1005,1025-4094 设置交换机间链路 干道（trunk）（此端口与2950交换机相连） set port channel 4/5-6 mode off ! #module 5 empty ! #module 6 : 48-port 10/100BaseTX Ethernet set vlan 20 6/1-48 set spantree portfast 6/6-12 enable 设置速端口 （减少收敛时间） ! #module 7 empty ! #module 8 : 48-port 10/100BaseTX Ethernet set vlan 20 8/1-48 ! #module 9 empty ! #module 15 : 1-port Multilayer Switch Feature Card ! #module 16 : 1-port Multilayer Switch Feature Card end 两个引擎模块上各有一个msfc2 模块互为热备且转发路由互为负载均衡。MSFC2多层交换模块提供交换机vlan间路由。 引擎一上msfc2配置（r1）： 操作系统为cisco ios 12.1 Current configuration : 3422 bytes ! version 12.1 service timestamps debug uptime service timestamps log uptime service password-encryption ! hostname r1 设置路由器主机名 ! boot system flash bootflash:c6msfc2-psv-mz.121-8a.E5 载入操作系统 enable secret 5 $1$gZQ6$pGpbM7yPeCoyTw1oGI9L/0 设置口令 ! username lxd password 7 060A1725 ip subnet-zero ! ! interface Vlan10 进入vlan10接口 ip address 10.35.50.61 255.255.255.192 配置vlan10 ip地址 no ip redirects standby priority 150 preempt 设置热备份路由权限（数字越高越大） standby name webserver 设置端口名字 standby ip 10.35.50.62 设置虚拟网关IP地址 ! interface Vlan20 ip address 10.35.50.125 255.255.255.192 no ip redirects standby priority 150 preempt standby name txk standby ip 10.35.50.126 ! interface Vlan30 ip address 10.35.50.189 255.255.255.192 no ip redirects standby priority 150 preempt standby name zhiandadui standby ip 10.35.50.190 ! interface Vlan35 ip address 10.35.50.253 255.255.255.192 no ip redirects standby priority 150 preempt standby name wangguanzhongxin standby ip 10.35.50.254 ! interface Vlan50 ip address 10.35.51.29 255.255.255.224 no ip redirects standby priority 50 preempt standby name julingdao standby ip 10.35.51.30 ! interface Vlan51 ip address 10.35.51.61 255.255.255.224 no ip redirects standby priority 50 preempt standby name zhenfawei standby ip 10.35.51.62 ! interface Vlan53 ip address 10.35.51.125 255.255.255.192 no ip redirects
standby priority 50 preempt standby name xinjingdadui standby ip 10.35.51.126 ! interface Vlan55 ip address 10.35.51.253 255.255.255.128 no ip redirects standby priority 50 preempt standby name office standby ip 10.35.51.254 ! interface Vlan56 ip address 10.35.52.125 255.255.255.128 no ip redirects standby priority 50 preempt standby name 110 standby ip 10.35.52.126 ! interface Vlan57 ip address 10.35.52.157 255.255.255.224 no ip redirects standby priority 50 preempt standby name zhanbaoke standby ip 10.35.52.158 ! interface Vlan58 ip address 10.35.52.189 255.255.255.224 no ip redirects standby priority 50 preempt standby name bagongshi standby ip 10.35.52.190 ! interface Vlan59 ip address 10.35.52.221 255.255.255.224 no ip redirects standby priority 50 preempt standby name zhenzhizhu standby ip 10.35.52.222 ! interface Vlan60 ip address 10.35.55.125 255.255.255.128 no ip redirects standby priority 150 preempt standby name sunserver standby ip 10.35.55.126 ! interface Vlan70 ip address 10.35.55.250 255.255.255.128 no ip redirects standby priority 50 preempt standby name huaweirouter standby ip 10.35.55.254 ! interface Vlan80 ip address 10.35.59.125 255.255.255.128 no ip redirects standby priority 50 preempt standby name chuoguanshu standby ip 10.35.59.126 ! router ospf 100 打开ospf路由进程，进程号为100 log-adjacency-changes network 10.35.50.0 0.0.0.63 area 2 对网段发布启用ospf协议，区域号为2 network 10.35.50.64 0.0.0.63 area 2 network 10.35.50.128 0.0.0.63 area 2 network 10.35.50.192 0.0.0.63 area 2 network 10.35.51.0 0.0.0.31 area 2 network 10.35.51.32 0.0.0.31 area 2 network 10.35.51.64 0.0.0.63 area 2 network 10.35.51.0 0.0.0.127 area 2 network 10.35.51.128 0.0.0.127 area 2 network 10.35.52.0 0.0.0.127 area 2 network 10.35.52.128 0.0.0.31 area 2 network 10.35.52.160 0.0.0.31 area 2 network 10.35.52.192 0.0.0.31 area 2 network 10.35.55.0 0.0.0.127 area 2 network 10.35.55.128 0.0.0.127 area 2 network 10.35.59.0 0.0.0.127 area 2 ! ip classless ip route 0.0.0.0 0.0.0.0 10.35.55.253 设置默认路由 no ip http server ! snmp-server community jyganet RO ! ! line con 0 line vty 0 4 设置telnet 口令 password 7 082D544A login local ! end 引擎二上msfc2配置（r2）： 操作系统为cisco ios 12.1 version 12.1 service timestamps debug uptime service timestamps log uptime service password-encryption ! hostname 6509r2 ! boot system flash bootflash:c6msfc2-psv-mz.121-8a.E5 enable secre
标签：